You'll Never Guess This Replace Door Lock's Benefits > 자유게시판

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to replace lock in upvc door Door Locks

Your first security measure is your door lock. It will stop unauthorized entry into your home. The signs of wear and tear and even instances such as moving into a new house or break-ins, can necessitate the necessity of replacing your lock.

To begin, determine your cylinder size by measuring the distance between the adjustment screw and the center of the cylinder knob. This measurement will allow you to purchase the correct-sized lock.

Deadbolt

If you're looking to ensure that your upvc door replacement lock is secure against burglars, it's a good idea to install deadbolts. The bolt extends into the strike plate that is on the door frame when it's locked, making it more difficult for a burglar to gain entry into the door. A single-cylinder deadbolt is activated using a key on the outside and a thumb-turn piece located on the interior. A deadbolt is only effective when it's properly installed however.

First, you'll need to determine if the replacement upvc door locking mechanism has a hole to install a deadbolt or if it has to be bored. Using the template that comes with the lock installation kit mark the location of the deadbolt hole on the door's surface. Use your tape measure to determine the height of the deadbolt. Then, replace Door Lock mark the height on the side of the door and use a speed square to draw a straight line across the mark you made for the bolt hole.

Next, use a power drill to drill this hole until it is on the opposite side of the door. This could take a bit of time. Sand the hole and the edge of the door to smooth it. It's also an excellent idea to stain or paint the door at this point.

Once the door is ready remove any screws visible on the existing deadbolt. This will reveal the back and front assemblies of the deadbolt, as well as the internal bolt. Then unscrew the old bolt and replace door lock it by the new bolt to match your door hardware. The bolt is usually connected to a set plate which you'll need to unscrew. Once this is done it is time to chisel the area for the strike plate that is on the door frame.

If your strike plate isn't aligned properly, it's likely because the previous installer didn't correctly mortise it or a weatherstripping was installed and altered the strike position. You'll need to re-mortise your strike plate and possibly even the deadbolt to fix this issue. Close and lock the deadbolt when you've completed this step. Test the deadbolt by closing and locking it once the bolt has been extended into the strike plate.

Knob

It can make your business and home less secure if the door knob is worn. It could also make opening or closing the door more difficult, which is why it is an ideal idea to replace upvc door lock the knob. Replacing knobs is an simple DIY project that shouldn't take more than 30 minutes to complete. You can use a screwdriver as well as pliers to get rid of the old knob or handle, but be careful not to damage any of the other components on the door.

Spray WD-40, or another dry lubricant on the mechanism of your door knob prior to you begin. This will allow the new lock slide effortlessly when you turn it. It's essential to select a quality knob and handle that matches the doors you currently have to ensure that the lock is operating properly. If there's no match, you'll need to buy an additional doorknob and latch plate.

To begin the replacement upvc door locking mechanism process, first look over the knob or handle to determine the screws that hold it in place. If there aren't screws, you can use the screwdriver to wedge the cover plate into the hidden screws plate.

After removing the old knob take it apart and look for Replace door lock signs of rust and damage. If the knob shows any marks or scratches, you'll have clean it. Otherwise, it shouldn't require any major work.

Install the new knob. Begin by examining the two new knobs to ensure that you're choosing the right one for your door. You should select one that has an extending rod that's designed to lock into the second knob's rod mechanism. After you've inserted the new knob into the hole, slide it into the latch.

Thread the latch plate screws downwards and then test the spring by pressing down on it several times. The latch should pop up each time. Install the second knob and lock it to the rod mechanism of the first knob. Thread the long screws from the doorknob's interior through the cylinder holes on the outside knob and secure it in its place.

Latch

A latch is a piece of metal that extends through the doorjamb to hold it shut. It is operated with a knob or handle on the inside of the door, or a thumb turn on the exterior side of the door. A latch can be secured with a deadbolt to keep intrusions from piercing the door's glass. It also offers protection from the accidental or deliberate closing of the door by children or pets. A latch can be installed using one cylinder deadbolt or a double cylinder deadbolt, based on the level of security you prefer.

Installing a deadbolt can be the same as installing a latch but there are some differences. First, determine the setback of the doorjamb using an instrument to make sure the new lock will fit. The setback is the distance from the edge of the doorjamb to the middle of the hole to accommodate the faceplate of the latch. A standard setback is 2 3/8 to 2 3/4 inches. If you have a greater setback, you may have to purchase a more substantial latch from a hardware shop or locksmith.

The next step is to drill an edge bore hole in the doorjamb for the latch plate. Utilize a chisel to make the mortise for the latch. Make sure that the depth is enough for the faceplate to be flush with the doorjamb. Tape the strikeplate in place to ensure that it's positioned properly.

If the strike is placed too high, the door can be pushed in or pressure applied to it with a crowbar or tire iron. This can also crack the doorjamb. To correct this issue, the strike can be reduced by drilling a second hole in the doorjamb and cutting out the core of the hole that was previously drilled.

The final step is to mount the new strike plate, which is done by screwing it over the screw holes that are already in place. Utilize wood putty to fill in any existing bolt holes or screw holes which aren't going to be used. Once the putty has dried then sand it to a smooth finish.

Strike

An electric strike is a metal piece where the deadbolt and latch engage when the door is closed. It is a vital part of the lock's security, as it prevents the door from opening and gives an additional barrier to force or kick. If a door has been equipped with an electric strike, it can only be opened with a key or the control unit that controls its electrical impulses.

In the past, installing an electronic strike required cutting a portion of a doorjamb to remove the latchbolt on a cylindrical lock from the pocket inside the strike. This modification is not only ugly however, it also exposes the mechanism for the latchbolt and the keeper to intruders.

Recently, several electric strikes manufacturers have created a "No Cut" kind of strike that doesn't require a cutout to operate. These strikes use a special design that allows the latchbolt and keeper to slide into the pocket without causing damage to the doorjamb's faceplate.

The strike is fitted with an internal ramp that raises the latchbolt and keeper whenever it receives an indication from the reader. The latchbolt and keeper are pushed up the ramp by the retract. When the door is closed, the deadbolt stays extended and the latchbolt is retracted into the keeper.

Installing an electric strike can be a simple process, especially if you are replacing the strike on a previous door. If you are upgrading an existing access control system to an electric strike, you must ensure that the new system is compatible. Also, you must ensure that the strike is properly connected to your access control system and is set up to operate in a safe manner.

Upgrade your strike plates with heavy duty strike plates to prevent the entry of unauthorized persons. These plates can be fitted with up to six screws of three inches instead of two screws of three-fourths inches. The longer screws make it harder for someone to break the frame and reach inside to turn the thumb turn piece of a single deadbolt cylinder.